Atlas Copco CS14 Diamond Core Drill ID: 1355401

Atlas Copco CS14 Diamond Core Drill

• Make: Atlas Copco
• Model: Christensen CS14
• Type: Diamond Core Drill
• Condition: Used, Reported in Good Condition
  
  
• General Model Specifications:
  
  
  • Depth Capacity Coring: (Wireline or Conventional)
    • B Wireline: 1,540m (5,052ft)
    • N Wireline: 1,200m (4,042ft)
    • H Wireline: 800m (2,695ft)
    • P Wireline: 475m (1,558ft)
      
      
  • Main Hoist:
    • Single Line Capacity: Bare Drum 80kN (18,000 lbs.)
    • Line Speed: Bare Drum 44m/min (148ft/min)
    • Cable Size: 35m (118ft) x 16mm (10/16in)
      
      
  • Wireline:
    • Capacity:
      • 1,830m (6,000ft) of 4.76 mm (3/16in)
      • 975m (3,200ft) of 6.35 mm (1/4in)
    • Line Pull:
      • Bare Drum: 11.9kN (2665lbs.)
      • Full Drum: 3.0kN (668lbs.)
    • Line Speed:
      • Bare Drum: 114m/min (374ft/min)
      • Full Drum: 453m/min (1,486ft/min)
        
        
  • Mast and Feed System:
    • Feed Travel: 3.5m (11.5ft)
    • Feed Speeds: Fast and Slow with Variable Control
    • Thrust: 59.6kN (13,390lbs.)
    • Pull: 138kN (31,020lbs.)
    • Drilling Angle: 45° to 90° degrees
    • Rod Pull Length: 6.09m (20ft)
      
      
  • Power Unit:
    • Manufacture: Cummins
    • Model: QSB6.7
    • Volume: 6.7L 6-Cylinder
    • Power: 208HP (153kW)
    • RPM: 1800
      
      
  • Hydraulic System:
    • Primary Pump: 28MPa – 242 L/min (4,061 PSI – 63.9 Gal/min)
    • Secondary Pump: 20MPa – 122 L/min (2,901 PSI – 32.2 Gal/min)
    • Auxiliary Pump: 21.5MPa – 47 L/min (3,118 PSI – 12.4 Gal/min)
    • Hydraulic Oil Cooling: Air
      
      
  • Drillhead and Spindle Speeds:
    • Power: Hydraulic Motor – Variable Speed/Reversible
    • Final Drive: 4in Chain-Driven in Oil Bath – 2.5 Ratio
    • Spindle (Inner Diameter): 117mm (4.625in)
    • Spindle Speeds:
      • 1st: 6.63:1, 117-196 RPM, 5,113-3,051 Nm (3,771-2,250 ft-lbs.)
      • 2nd: 3.17:1, 245-410 RPM, 2,445-1,459 Nm (1,803-1,076 ft-lbs.)
      • 3rd: 1.72:1, 451-756 RPM, 1,326-792 Nm (978-584 ft-lbs.)
      • 4th: 1.00:1, 776-1,300 RPM, 771-460 Nm (569-340 ft-lbs.)
    • Range Selection: Manual Control from Operator’s Station
    • Hinged Head: Swing Away
      
      
  • Chuck Assembly:
    • Type: Hydraulic Open, Spring Closed
    • Maximum Inside Diameter: 117mm (4.625in)
    • Holding Capacity: 18,143 kg (40,000 lbs.)
      
      
  • Rod Holder:
    • Type: Hydraulic Open, Gas Spring Closed
    • Maximum Inside Diameter: 210mm (8.3in)
    • Holding Capacity: 13,000 kg (28,660 lbs.)
      
      
  • Drill Base Supports:
    • Trailer Mounted Rig, Wheels
    • Support: 4 Hydraulic Jacks
      
      
  • Standard Equipment:
    • Hydraulic P-Size Rod Holder
    • 4 Hydraulic Leveling Jacks
    • Towing Package
    • Fuel Tank: 200 Liters (53 Gal)
    • Fuel Filter & Water Separator
    • Hydraulic Mast Dump
    • Mast in Two Sections
    • Large Crown Sheave Wheel
    • Wear Lines on Lower Mast
    • Safety Guards
    • Hydraulic Oil Reservoir Fill Pump & Filtration
    • Hydraulic Mast Raise
      
      
  • Overall Dimensions:
    • Length: 27.65ft (8,382mm)
    • Width: 10.5ft (3,200mm)
    • Height: 10.5ft (3,200mm)
    • Weight: 7,000 kg
      
      
• Location: Western USA

View More Diamond Core Drills