Balemaster Auto Tie Baler ID: 264432

• Model : BB3230TQ-8
• Serial # B235-01-6001548
• Automatic auto-tie system AT-1-BB4
• 30HP / 600volt
• 8" Cylinder
• 30'' x 32'' feed opening
• Location: Eastern Canada

View more Recycling Equipment

Schoma 40 Ton Tunnel Locomotive ID: 177408

• Year: 2005.
• Drive system: Diesel-hydrostatic.
• Usage: tunnel & underground.
• Track gauge: 1000 mm (can be changed to 900 mm).
• Deutz 250 HP diesel engines.
• Max. speed: 32 km/h.
• Min. curve radius: 40 m.
• Min. track clearance: 15 mm.
• Structure:
  • Continuous main frame in box design.
  • Engine compartment with access flaps for maintenance purposes.
  • Fuel tank mounted on main frame and protected against collisions.
  • Rail guards adjustable in height.
  • Electric components inside enclosed cubicle in the drivers cabin.
• Locomotive main frame:
  • Main frame in box design with high torsion resistance.
  • MAG welded.
  • Side plates with cut-outs for inspection of axle gears, brake gears, etc.
  • 2 lifting points at both sides.
• Operators cabin:
  • 2 door cabin.
  • One operators desk with ergonomic arrangement of controls and levers.
  • Front window equipped with wipers.
• Fuel system:
  • Filler caps at both sids of the locomotive.
  • Fuel gauge on operators panel.
  • Fuel tank capacity: 600 L approx.
• Quantity: 1.

View more Diesel Operated Locomotives

TIME Advanced Stoper Longhole Drill ID: 1398203

TIME Advanced Stoper Longhole Drill

• Make: TIME
• Model: Advanced Stoper
• Year: 2023
• Type: Longhole Drill
• Condition: New, No Hours
• Drill: S36 IR Drifter Drill
  • Aluminum Feed
  • Heavy-Duty Centralizer (Used)
  • Nominal Diameter: 35 - 89 mm (1.38in-3.5in)
  • Nominal Length: Up To 46m (Up To 150ft)
  • Reamed Diameter: Up To 127mm (Up To 5in)
  • Blows/Minute: 1630 @ 500 kPa (1630 @ 72.52 PSI)
  • Air Consumption: 14m³/min @ 500 kPa (494.41 CFM @ 72.52 PSI)
• Traverse: 5ft Traverse
  • Side to Side Hole Positioning of 66in (168cm)
• (3) Helac Actuators for Increased Stability and Less Wear Parts
  • 135° Dump, 360° Radial and an Optional 180° Pivot Positioning
    
    
• Carrier: 
  • 30HP Radial Piston Air Motor (@1200 RPM)
    • 116 PSI & 890 CFM Air Delivery
  • Tandem Gear Hydraulic Pump
    • 1.91in³ Per Rev. @3000 PSI
  • High Quality Proportional Directional Control Valves
  • High Quality Motion Control and Cross-Port Check Valves 
  • Two Lever Pilot (Low) Pressure Tethered Remote Tramming Valve 
  • Skid Steering with Independent Port and Starboard Wheel Drives 
  • Planetary 4-Wheel Hydraulic Drive with Fail-Safe Brakes 
  • 4 Independent Heavy-Duty Jacks with Load Lock (Cross Port Check) Valves for Leveling 
  • Tow-Bar and Dis-Engaging Wheel Drives for Towing 
  • Rotation Barrier – Double Hinged (Opens from the Left or Right Side)
    
    
• Location: Eastern Canada

View More Jumbo Drills

CAT 1500 kW Generator ID: 218351

• Year: 1987.
• 150 kW
• Dulce valve and Huron actuator.
• CAT 3516 engine.
  • 2168 HP.
  • 1800 RPM.
  • 277/480 volt.
  • 3 phase.
• Generator Model: SR-4
• EMCP digital control panel.
• 2000 amp main-line circuit breaker.
• Weather enclosure.
• 200 gallon (approx.) sub-base day tank.
• 284 in. long x 106 in. wide x 123 in. high.
• Weight: 40,000 lbs.
• Location: Europe.

 View more Diesel Generators

Atlas 3 ½ in. x 5 ½ in. Laboratory Jaw Crusher ID: 665465

• Jaw Opening: 3 ½ in. x 5 ½ in
• Mounted on 2 ft. x 3 ft. Common Base 
• 2 HP Motor & Drive
• Flywheel Guard 
• Drive Guard 
• Feed Hopper and Ore Pan
• Location: British Columbia, Canada

View more Lab Jaw Crushers

General Electric Stop/Start ID: 1388746

General Electric Stop/Start

MAX V: 600V

CR2943NAI02CA

• Location: Savona, British Columbia, Canada

Baldor 7.5 HP Motor ID: 191305

• ID No.: F-6670-01-629.
• Volts: 230/460V.
• RPM: 3490.
• Frame: 213T.
• Phase: 3.
• Shaft Length: 3 3/4 In.
• Shaft Diameter: 1 1/4 In. 

View more 7.5 HP Motors 

Siemens 200 Amp Disconnect ID: 157604

• 240V.
• 2 wire.
• Single phase.
• Suitable for service entrance.

Please contact us for more information.

View more 200 Amp Disconnects

Allen-Bradley Power Switch ID: 1396344

Allen-Bradley Power Switch

2 Pole Only

3/4HP

115-230V DC MAX

1 or 2 Pole

1HP

120-240V AC MAX

• Location: Savona, British Columbia, Canada

2000 Amp 3 Pole Breaker ID: 516613

2000 Amp

3 Pole

Stainless Steel 10 cu. ft. Conical Hopper ID: 193293

• 40 In. Diameter x 45 In. Overall Height.
• Top has a 24 In. Square Flanged Inlet.
• Three level probes.
• 4 In. Inlet Pneumatic Vent Line.
• Outlet of Hopper is a round 12 In. Diameter Flanged Outlet. 

View more Hoppers

Red White 4 in. Gate Valve ID: 730122

• Size: 4 in.
• Class: 125
• Body: C.I
• Body Seat: Bronze
• 8 Bolt Flanged Ends
• Location: British Columbia, Canada

View more Gate Valves

Baldor 5 HP VFD ID: 187829

• Input
  • 460 VAC
  • 50/60 Hz
• Output
  • 460 VAC
  • 0 - 400 Hz
• Cat #: ID15405-E
• Quantity 1

View More 5 HP VFDs

Phoenix WX Belt Filter ID: 1377305

Phoenix WX Belt Filter

• Make: Phoenix Process Equipment
• Model: WX-2.0 Belt Filter
• Size: 2.0 Meters
• Condition: Used
• Comes with:
  • Control Cabinet
  • Air Compressor 
  • Spare Belts
    
    
• Features:
  • Heavy All-Welded Main Frame
  • Modular Construction 
  • Continuous Automatic Operation 
  • Open Design 
  • Epoxy Over Zinc Coated Frame 
  • Pneumatic Belt Tracking/Tensioning 
  • Standard, Extend, Independent or Dual Gravity Zone
    
    
• Description: 
  • 1. Preconditioning (Flocculation): Most applications require the addition of polymers to the slurry prior to dewatering. The addition of these flocculants results in the agglomeration of solids, releasing free moisture. An inline mixer is provided for proper dispersal of polymer into the feed.
  • 2. Feed Distribution: The slurry is fed to a specially designed head box, where the material is evenly distributed for more efficient use of the filtering area.
  • 3. Gravity Drainage: Free moisture is separated from the solids by drainage through the moving filter belt.
  • 4. Wedge Pressure: Material advancing from the drainage zone is deposited into the adjustable wedge zone. Pressure is gradually applied as the upper and lower belts converge to form a “cake sandwich.”
  • 5. Compression/Shear: The belts then follow an “S” path through a series of compression rollers. The surface pressure created by belt tension squeezes additional moisture from the solids. Simultaneous shearing of the material opens additional voids for moisture release. The belts part, leaving a dry cake.
  • 6. Solids Discharge: Cake is separated from the belts by doctor blades and discharged.
    
    
• Applications:
  • Coal Refuse
  • Scrubber Effluent 
  • Pulp and Paper Effluent 
  • Domestic Biological Waste 
  • Textile Wastewater 
  • Grease Trap Waste 
  • Water Treatment Sludge 
  • Aggregate Tailings 
  • Food Process Waste 
  • Chemical Waste 
  • Municipal Wastewater 
  • Dredging Slurries
    
    
• Location: Eastern USA

View More Belt Filters