Quotes

Wanted Equipment Sell Your Equipment Financing - Apply now

Equipment Quotes

MTI LT270 1.5 Yard Scooptram ID: 1259052

MTI LT270 1.5 Yard Scooptram

Make: MTI
Model: LT270
Size: 1.5 Yard
Hours: 3,155.6
Condition: Used, Reported in Good Condition
Canopy: ROPS
Midship is Tight
General Model Specifications:
- Capacities:
  - Tramming Capacity: 2,722 kgs (6,000 lbs)
  - Hydraulic Breakout Force Lift: 6,043 kgs (13,322 lbs)
  - Hydraulic Breakout Force Tilt: 5,372 kgs (11,844 lbs)
  - SAE breakout force: 4,735 kgs (10,441 lbs)
  - SAE static Tipping Load: 9,662 kgs (21,301 lbs)
  - Bucket: 1.5yd³ (1.2m³)
- Overall Dimensions
  - Tramming Length: 6,365mm (20ft 10.5in)
  - Width Overall: 1,514mm (4ft 11.5in)
  - Height (Canopy): 1,935 mm (6ft 4in) Length:
  - Rear Axle to Bumper: 2,288mm (7ft 6in)
  - Centre Hinge to Rear Axle: 1,041mm (3ft 5in)
  - Centre Hinge to Front Axle: 1,045mm (3ft 5in)
  - Reach: 1,218mm (4ft)
  - Height (Top of Hood): 1,493mm (4ft 10.75in)
  - Height Ground Clearance: 204mm (8in)
  - Height Dump Clearance: 1,111mm (3ft 7.5in)
  - Height Bucket Pin: 2,075mm (6ft 10in)
  - Height Bucket Raised: 3,266mm (10ft 8.5in)
  - Maximum Width RF: 1,422mm (4ft 8in)
  - Outside Radius: 4,374mm (14ft 4in)
  - Inside Radius: 2,380mm (6ft 17.75in)
  - Turn Angle: 37° Degrees
  - Dump Angle: 38° Degrees
  - Roll Back Angle: 50° Degrees
Location: Eastern Canada

View More Scooptrams

View details Remove

Munson Dual Shaft Shredder ID: 354265

Model: Titan 28
20HP
- 230 volt
Low Speed / High Torque
28in. x 15in. Feed Opening
Location: Western USA

View more Shredders

View details Remove

Diamond Core Drill Sloop with BQ Drill String ID: 235275

Dimensions: 146" L x 85" W x 75" H
Skid: 12" x 7" x 3/8 H Beam
Completed with:
- BQ Drill Rod
  - 330 Pieces
  - 10' Long
- NQ Drill Rod
  - 8 Pieces
  - 10' Long
- HW Casing
  - 33 Pieces
  - 27" Long
- NQ Core Barrels
  - 2 Pieces
  - 5' Long
- NQ Core Barrels
  - 2 Pieces
  - 10' Long
- BQ Core Barrels
  - 2 Pieces
  - 10' Long
Location: Western Canada

View more Drill Rods

View details Remove

Whemclone 20 in. Cyclone ID: 960652

Size: 20 in.
Rubber Lined
Location: British Columbia, Canada

View more Cyclones

View details Remove

Atlas Copco CS10 Diamond Drill ID: 1173673

Atlas Copco CS10 Diamond Drill

Make: Atlas Copco
Model: Christensen CS 10
Hours: 600 Hours
Depth Capacity: Standard
- B: 1,200m (3,936ft)
- N: 800m (2,624ft)
- H: 600m (1,968ft)
- P: 400m (1,312ft)
Rotation Unit:
- Power, Hydraulic Motor: Variable Speed/Reversible
- Final Drive: Gear Driven
- Spindle (Inner Diameter): 124mm (4.88in)
- Max Torque: 6,790 Nm (5,008 lbf)
- Max Speed: 1,300 RPM
Spindle Data
- Low Speed:
  - Ratio: 17.55:1
  - Speed: 80-200 RPM
  - Torque: 6,790-2,670 Nm
- High Speed:
  - Ratio: 2.70:1
  - Speed: 510-1300 RPM
  - Torque: 1,070-420 Nm
Chuck Assembly
- Type: Hydraulic Open, Spring Close
- Max Diameter: 124mm (4.88in)
- Holding Capacity: 178 kN (40,000 lbf)
Mast and Feed System:
- Feed Travel: 1.83m (6ft)
- Feed Speeds, With Variable Control: High and Low
- Thrust: 59.6kN (13,390lbs)
- Pull: 90kN (20,200lbs.)
- Drilling Angle: 45°–90° Degrees
- Rod Pull Length: 6m (20ft)
Rod Holder:
- Type: Hydraulic Open, Gas Spring Closed: BO to PO Rods/PW Casing
- Max Diameter: 144mm (5.7in)
- Clamping Capacity: 130kN (29,922lbs)
Power Unit: Caterpillar 3054E, Tier II
- Volume 4.4 Liters 4-Cyl (1.2g)
- Power, Tier III: 80kW (108HP)
- RPM: 2,000
- Cooling System: Water
- Electrical System: 24V
Main Hoist:
- Single Line Capacity, Bare Drum: 53.4kN (12,000lbs)
- Line Speed, Bare Drum: 51 m/min (167 ft/min)
- Cable Size: 27m x 16mm (89ft x 10/16in)
Wireline Hoist:
- Capacity: 2,000m of 4.76mm (6,561ft of 3/16in)
- Line Pull:
  - Bare Drum: 13 kN (2,922 lbs.)
  - Full Drum: 4 kN (899 lbs.)
- Line Speed:
  - Bare Drum: 130 m/min (427 ft/min)
  - Full Drum: 420 m/min (1,378 ft/min)
Drill Base Supports:
- Mount/Base System: Trailer Mounted Rig with Four Wheels (215/75R17.5) and Towing Package
- Pad Diameter: Ø220mm (8.7in)
- Leg Adjust Range: 550mm (21.7in)
Trido
- Model: Trido 140H
- Flow: 140 l/min (37 gal/min)
- Pressure: 70 bar (1,015 psi)
Hydraulic System:
- Primary Pump: 28 MPa, 242 l/min (4,061 psi, 64 gal/min)
- Secondary Pump: 20 MPa, 122 l/min (2,901 psi, 32.2 gal/min)
- Auxiliary Pump: 21.5 MPa, 47 l/min (3,118 psi, 12.4 gal/min)
- Hydraulic Oil Cooling: Air
Working Dimensions:
- Length: 5,780mm (228in)
  - Mast @ 45°: 8,197mm (323in)
- Width: 2,200mm (87in)
- Height: 11,120mm (438in)
  - Mast @ 45°: 8,564mm (341in)
- Weight: 5,500kg (12,130 lbs.)
Transport Dimensions:
- Length: 5,946mm (234in)
- Width: 2,200mm (87in)
- Height: 2,192mm (86in)
- Weight: 5,500kg (12,130 lbs.)
Included:
- Cutter Head
- 500ft of 6in Steel
- 500ft of 8in Steel
- Extra Drill Bits
Location: Southeast USA

View More Diamond Core Drills

View details Remove

Action Mining M7 Wave Concentrating Tables ID: 1013092

Model: M7 Micron Mill Wave Table.
Capacity: 1,500 - 2,500 lbs. of head ore material per hour.

Recovery of gold particles: Between 10 mesh and microscopic.

80-99% of gold recovery from classified black sands.
92-99% of gold recovery.

Water requirements: 5-12 GPM.

2 adjustable water spray bars.

Table top and hopper constructed of fiberglass.

Vacuum-sealed and gel-coated in blue finish.
Adjustable table top.

1/2 HP electric motor drive.

110V AC, 60 Hz.

Steel frame with yellow powder coated epoxy paint.

Shipping information:

Dimensions (L x W x H):

61 in. x 32 in. x 39 in.

1.55 m x 0.81 m x 0.99 m.

Weight:

409 lbs. / 186 kg.

Located: Western Canada

View more Gold Concentrating Tables

View details Remove

Freightliner M2 Roll Back Truck ID: 135074

Freightliner M2 Roll Back Truck.
- Year: 2005.
- 393,000 km.
- Equipped with:
  - Caterpillar C7 engine.
  - 9 speed transmission.
  - Tandem axle.
  - Ledwell 28 ft. deck.
  - Braden 20,000 lb winch.
  - Air conditioning.