Equipment Quotes
Allen Bradley PowerFlex700 5 HP VFD ID: 172464
- Input
- 475 - 632 VAC
- 5.3 Amps
- 47-63 Hz
- Output
- 0 - 600 VAC
- 6.1 Amps
- 0 - 400 Hz
- Cat #: 20BE6P1A0AYNANDO
- Series B
- Line Reactor
- Mounted in Allen Bradley 2100 Series MCC Bucket
- Control Transformer
- 0.080 KVA
- 600/120 VAC
- 10 Amp Class J Fuses
- Cooling Fan
- Controller on Door
- Will Sell VFD Seperately
View More 5 HP VFDs
Manufacturer: | ALLEN BRADLEY |
490kW CAT 3508 Natural Gas Generator ID: 1222590
490kW CAT 3508 Natural Gas Generator
- Make: Caterpillar
- Model: 3508
- Duty: Continuous
- Year: 1998
- Condition: Used, Reported in Very Good Condition
- Portable/Stationary: Portable, Skid Mounted
- Engine: Caterpillar Engine Model 3508 STD Gas
- Hours: 4.5 Hours Since New
- Oil: Capacity - 227 L (60 U.S. Gal)
- Radiator: Air to Air, Charge Air Cooled, Capacity - 309 L (81.6 U.S. Gal)
- Generator: CAT SR4B
- kVA/kW: 490kW (612 kVA)
- RPM: 1500 RPM
- Voltage: 415/240 Volts
- Amperage: 883 Amps
- Frequency: 50Hz
- Phase: 3-Phase
- Control Panel: Caterpillar Control Panel
- Additional Information:
- Skid Mounted
- Gas Train
- Overall Dimensions: Approx.
- Length: 144in
- Width: 85in
- Height: 84in
- Weight: 16,800 Lbs (7627 Kgs.)
- Location: Europe
View More 501-1000kW Diesel Generators
Puritan Magnetics 16 in. Wide Cross Belt Magnet ID: 516929
- Model: CSBLB24POWR
- Belt: 16 in. Wide x 54 in. Long
- Magnet Dimensions: 16 in. Wide x 22 in. Long x 8 in. Deep
- Magnet strength 1500 Gauss.
- Head and Tail Pulley: 8: Dia. x 18 in. Long
- Overall Dimensions: 36 in. Wide x 54 in. Long x 18 in. Deep
- Right Angle Gear Head Motor
- Ratio: 15:1
- Tigear²
- Part/Model: 20Q15H56
- Baldor Motor
- 1 HP
- 230/460 Volt
- 1760 RPM
Frame: 56C
- Location: British Columbia, Canada
View more Belt Magnets
1979 Grove TM 875 80 Ton Crane ID: 1242367
1979 Grove TM 875 80 Ton Crane
- Make: Grove
- Model: TM 875
- Capacity: 80 Tons
- Type: Hydraulic
- Year: 1979
- Hours: 3,953 Original Hours
- Miles: 14,100 Original Miles
- Condition: Used, Reported in Good Condition, Job Ready
- Dual Engines
- Carrier Engine: CAT 3206
- Super Structure Engine: CAT 3208
- Latest Load Electronics
- See Spec Sheets For More Info
- Location: Southwest USA
View More Mobile Cranes
Cefco 400 Amp 250 Volt Fuse ID: 526253
Amp: 400
Volt: 250 or less
One Time Fuse
Gorman Rupp 6 in Diesel Trash Pump ID: 180644
- Inlet: 6 in. (150 mm).
- Outlet: 6 in. (150 mm).
- Max. capacity: 1810-2700 GPM.
- Max. head: 150-195 ft.
- Max. solids: 3 in. (75 mm).
Please contact us for more information.
- View more Trash Pumps
Littelfuse INDICATOR Time-Delay 20 amp fuse ID: 360843
20 AMP
600VAC or less
Class: RK5
Length: 5"
Time Delay
Cummins 80kW Diesel Generator ID: 1403559
Cummins 80kW Diesel Generator
- Make: Cummins
- Model: C80D6R-1401512
- Year: 2014
- Hours: 4,554.4 Hours
- Condition: Used Condition
- Duty: Standby/Prime
- Portable/Stationary: Portable - Trailer Mounted
- 3in Pintle Hitch
- Engine Model: QSB5-G2 Tier III
- Fuel Type: Diesel
- kVA/kW:
- Prime: 72kW (90kVA)
- Standby: 80kW (100kVA)
- Rotating Speed: 1800 RPM
- Voltage: 277/480 Volts - 12 Wire Reconnectable
- Current:
- Prime:
- 120/208 Volts: 249.8 Amps
- 120/240 Volts: 200.8 Amps
- 139/240 Volts: 216.5 Amps
- 277/480 Volts: 108.3 Amps
- Standby:
- 120/208 Volts: 277.6 Amps
- 120/240 Volts: 223.3 Amps
- 139/240 Volts: 240.6 Amps
- 277/480 Volts: 120.3 Amps
- Prime:
- Frequency: 60Hz
- Phase: Single or 3-Phase
- Multiple Voltage Selector Switch
- Enclosure: Sound Attenuated
- 27 Hour, 606 Liter Base Fuel Tank
- Overall Dimensions: With Trailer
- Length: 4,495mm (177in)
- Width: 1,905mm (77in)
- Height: 2,083mm (85in)
- Weight: 2,414 kg (5,322 lbs.)
- Location: Western Canada
View More 51-100kW Diesel Generators
Spendrup 42 in. Mine Ventilation Fan ID: 85043
- Model: EM 1120-70-6.
- 100 hp electric motor.
- 460 volt.
- 1765 rpm.
- 405T frame.
- Curve available.
- Please inquire for additional details.
Manufacturer: | SPENDRUP |
Montabert CPA X-TEND Boom ID: 1121082
Montabert CPA X-TEND Boom
- Make: Montabert
- Model: 24/20
- Condition: Good, Used
- Hours: 1200 Percussion Hours
- Feed Rail Looks to be in Very Good Condition
- Feed will take 24' Lead Steel and One 20' in Single Rod Holder
- T-51 Rods - Most Un-Used (x5)
- Comes With HC150 RP Montabert Drifter
- Includes Compressor (2,400 Hours)
CPA X-Tend Drilling Attachment
- Works with HC150 RP or HC160 RP Montabert Drifters (based on model type)
- 76-140mm Hole Diameter
- 45-51mm Rod Diameter
- 3.6-28 Meter Maximum Hole Length (based on model type)
- 2170-2530 Blows/min
- Wired Control Panel
- Dimensions: 32' 8" Long x 4' 5" Wide x 6' Tall
- Weight: 2820Kg
- Carrier Characteristics
- 22 to 35 Metric Tons
- 88kW (119HP) Minimum Power Required
- 195 l/min (51gpm) Required Oil Flow
- 195 bar (2800 PSI) Required Oil Pressure
These Attachments are ideal for the following applications:
- Quarry Holes for Blasting
- Trenches and Road Openings
- Utility Works
- Anchoring, Rock Bolting and Draining
- Rough Terrain Construction
- High or Long Reach Drilling
In Addition, The Drill Controls System Provides
- Straight Holes
- Best Productivity
- Easy Drilling in Difficult Location or Rock Conditions
HC150 Hydraulic Drifter
- 26-30 kW Maximum Output
- 37-50 kW Input Range
- 1,340-1,680 Nm Maximum Torque
- 76-115mm Hole Diameter
- 7,214-9,975mm Feed Length
- Type of Rod: T45, T51, T60
- Feed Swing: +/- 27°
- Air Requirement: 8,500-12,000 l/mm
- Weight: 190Kg
- Overall Length: 1,745mm
- Hydraulic Reserve Percussion
- Application: Tunneling, Benching, Long Hole
- Location: Western Canada
View More Drilling Parts and Accessories
Warman 300L Slurry Pump ID: 97729
- Model 300L.
- 14 in. x 12 in.
- Steel Lined.
- Overhead motor base.
- 5 vane steel impeller.
- Approx. Capacity:
- 2,400 gpm @ 200 ft.
- 13,000 gpm @ 130 ft.
- View Spec Sheet Below
- Location: Savona, British Columbia, Canada
General Electric 200 Amp 3 Pole Breaker ID: 586892
200 Amp
3 Pole
Cat No: FJ236200
600 V. AC
40C.
Ilsco D982 ID: 1304728
Ilsco D982
TA-500
CU-AL
500 MCM-4
In-floor Incline Belt Conveyor ID: 143321
- In-floor Incline Belt Conveyor.
- Consists of:
- 14 ft. horizontal section.
- 26 ft. inclined section.
- 60 in. wide belting.
- Belt is one continuous loop driven by head pulley motor.
- Consists of:
Please contact us for more information.
Siemens Size 4 Starter Contactor ID: 333603
- Size: 4
- Class: 3TF48
- Type: 1EC
- Coil: 120
- 3 Phase
- 60 Hz
- Location: British Columbia, Canada
View more Motor Starters
Hamilton H-3210 Parallel Shaft Gear Reducer ID: 75830
- 42.99:1 ratio.
- 59.3 hp.
- Size: H-3210.
Rietz 50ft³ Stainless Hopper with Auger Discharge ID: 1424432
Rietz 50ft³ Stainless Hopper with Auger Discharge
- Make: Reitz
- Model: C-12-K7208-6
- Condition: Used, Reported in Good Condition - Previously Used as Ore Hopper Feeding Rotary Dryer
- Construction: Stainless Steel
- Capacity: 50 Cubic Feet (Approx.)
- Top Section: 4ft x 5ft x 1ft
- Bottom Section: 4ft x 5ft x 3ft
- Top Opening: 4ft x 6ft
- Discharge: Auger Screw Discharge
- Diameter: 12in Dia.
- Open Top
- Drive: Siemens Electric Motor
- Power Output: 3HP
- Rotating Speed: 875 RPM
- Voltage: 460 Volt
- Frequency: 60Hz
- Phase: 3-Phase
- Diameter: 12in Dia.
- Location: Southwest USA
View More Hoppers
Sandvik AHM105 Voest Alpine Roadheader ID: 1205479
AHM105 Voest Alpine Roadheader
- Make: Voest Alpine (Sandvik)
- Model: AHM105 (MR620)
- Serial: AHM105019BG11
- Type: Roadheader - Hard Rock
- Hours: 6196.9
- Year: 2005
- Condition: Used
- Description: AHM105 (MR620) Hard-Rock Miner is an Electrically Powered and Crawler-Mounted Roadheader that is Engineered to Excavate Roadways and Galleries. This Heavy-Duty Machine has a Powerful Transverse Cutter Head Mounted on an Extremely Robust Telescopic Boom. It is Designed to Excavate Rock with High Compressive Strengths.
- Specifications:
- Machine Ground Pressure: 0.22 MPa
- Loading Table Width (Variable): 5.5m-6.4m
- Ground Clearance: 240mm
- Cutting Height Above Track Level: 5.3m-5.8m
- Cutting Width: 7.9m-8.5m
- Undercut Below Floor Level: 500mm
- Cutter Head Sprays: Jet Pipe
- Cutting Speed (50Hz): 1.4m/sec
- Navigable Cone Radius: 25m
- Navigable Basin Radius: 25m
- Navigable Slope Side Gradient: ±8/±9 gon
- Slope Upgrade/Incline Without Stabilizing: ±18/±20 gon
- Electric Supply Voltage (V/Hz): 1,000 Volt, 50Hz
- Cutter Motor (kW): 300
- Tramming Speed: 0-3.5m/min
- Total Installed Power (kW): 522kW
- Additional Information:
- Comes with Sea Can Full Of Parts
- Comes with Sea Can Full Of Parts
- Dimensions:
- Length: 12.2m
- Width: 3.6m - Table Width (2.6m - Tracks)
- Height: 2.4m
- Total Weight: 118 Tons Approx.
- Location: Western Canada
View More Roadheaders
Caterpillar 250 kW Marine Generator ID: 141991
- Caterpillar 250 kW Marine Generator.
- New/surplus.
- 397 hp @ 1800 rpm.
- 254/440V.
- 3 phase, 60 Hz.
- 254/440V.
- 397 hp @ 1800 rpm.
- New/surplus.
Please contact us for more information.
Manufacturer: | CATERPILLAR |
Square D 400 Amp Safety Switch ID: 192831
- Model: HU365.
- Volts: 600 VAC.
- Non-Fusible.
- 3 Pole.
View more 400 Amp Disconnects
1,150 Gallon Mixing Tank & Mixer ID: 1173276
1,150 Gallon Mixing Tank
- Size: 73" Diameter x 63" Tall
- Volume: 1,150 US Gallons
- 4 Internal Baffles:
- 51" x 6" x 1"
- 1" Gap to Tank Wall
- 6" Off Bottom
- Pedestal Tank Mixer
- Model: Dynamix DMX-5520J-2
- Mixer Shaft: 65.75" Long x 1.25" Diameter
- Propeller: Stainless Steel
- 19" Diameter
- Pitched Blade
- Comes with second 9.75" diameter radial blade propeller
- Medium Mixing Level
- Approx. 13" Off Bottom of tank
- 19" Diameter
- Mixer Motor: TEFC Electric Motor
- 2HP
- 1750 RPM
- 230/460V
- 60Hz, 3-Phase
- Inline Reducer:
- 11:1 Ratio
- 159 RPM
- Bridge on Top of Tank
- Made From 3" x 3" Angle
- Mixer Support Plates made from HDPE
- Mixer Mounting Plate Made From Stainless Steel
- 11" x 11" Plate
- 3" Diameter Center Hole
- 2.5" Tall 3/8 Studs Spaced 4" Apart
- Mixing Tank Lid
- Size: 73" Diameter x 19" Tall
- Notched for Mixer Mount Bridge
- Man Hole with Lid: 18" Diameter
- Center Hole for Mixer: 13" Diameter
- 8" x 7" Cutout
- Lifting Handles
- Fittings
- 2" Male and Female
- 6 Total - 2 Female, 4 Male
- 3 Holes @ 59.5" High
- 2 Holes @ 13.0" High
- 1 Hole @ 2.16" High
- Location: Savona, British Columbia, Canada
View More Agitators and Mixers
Armstrong 3in x 2.5in Centrifugal Water Pump ID: 1413439
Armstrong 3in x 2.5in Centrifugal Water Pump
- Make: Armstrong
- Model: 3x2.5x10 4030
- Condition: Used
- Suction: 3in
- Discharge: 2.5in
- Impeller: 10in
- Flow Rate @70ft: 190 GPM
- Drive: NIDEC Electric Motor
- Power Output: 7.5HP
- Rotation Speed: 1,765 RPM
- Voltage: 208-230/460 Volt
- Phase: 3-Phase
- Frequency: 60Hz
- Location: Eastern USA
View More Centrifugal Pumps
WEG 450 HP Induction Motor ID: 223856
- Volts: 2400.
- RPM: 1784.
- Ph: 3.
- Hz: 60.
- Frame: 5009/10/11T.
- Encl.: TEFC
- Weight: 2,165 kg.
- Location: Western Canada.
- Contact for more information.
View more 450 hp Motors
Manufacturer: | WEG |
Conn-Weld 8 x 20-1 Deck Incline Screen ID: 180868
- 8 ft. wide.
- 20 ft. long.
- Single deck.
- Circular motion prevents plugging.
- Thin bed depth.
- Trunion mounted for adjustable suspension.
- Spherical roller bearing mechanism.
- External counterweights for adjustable throw and uniform load across bearing.
- Oil lubrication.
View more Horizontal Screens
Cat 650 kW Generator Set ID: 220116
- CAT Engine Model: G399.
- RPM: 1200.
- Twin Turbos.
- Includes lot of spares parts.
- Quantity: 2
- Contact for additional details.
- Location: Europe.
View more Diesel Generators
Manufacturer: | CAT |