Allen Bradley PowerFlex700 5 HP VFD ID: 172464

• Input
  • 475 - 632 VAC
  • 5.3 Amps
  • 47-63 Hz
• Output
  • 0 - 600 VAC
  • 6.1 Amps
  • 0 - 400 Hz
• Cat #: 20BE6P1A0AYNANDO
• Series B
• Line Reactor
• Mounted in Allen Bradley 2100 Series MCC Bucket
• Control Transformer
  • 0.080 KVA
  • 600/120 VAC
• 10 Amp Class J Fuses
• Cooling Fan
• Controller on Door
• Will Sell VFD Seperately

 View More 5 HP VFDs

490kW CAT 3508 Natural Gas Generator ID: 1222590

490kW CAT 3508 Natural Gas Generator

• Make: Caterpillar
• Model: 3508
• Duty: Continuous
• Year: 1998
• Condition: Used, Reported in Very Good Condition
• Portable/Stationary: Portable, Skid Mounted
  
  
• Engine: Caterpillar Engine Model 3508 STD Gas 
  • Hours: 4.5 Hours Since New
  • Oil: Capacity - 227 L (60 U.S. Gal)
  • Radiator: Air to Air, Charge Air Cooled, Capacity - 309 L (81.6 U.S. Gal)
    
    
• Generator: CAT SR4B 
  • kVA/kW: 490kW (612 kVA)
  • RPM: 1500 RPM
  • Voltage: 415/240 Volts
  • Amperage: 883 Amps
  • Frequency: 50Hz
  • Phase: 3-Phase
  • Control Panel: Caterpillar Control Panel
    
    
• Additional Information:
  
  • Skid Mounted
  • Gas Train
    
    
• Overall Dimensions: Approx.
  • Length: 144in
  • Width: 85in
  • Height: 84in
  • Weight: 16,800 Lbs (7627 Kgs.)

• Location: Europe

View More 501-1000kW Diesel Generators

Puritan Magnetics 16 in. Wide Cross Belt Magnet ID: 516929

• Model: CSBLB24POWR
• Belt: 16 in. Wide x 54 in. Long
• Magnet Dimensions: 16 in. Wide x 22 in. Long x 8 in. Deep
• Magnet strength 1500 Gauss.
• Head and Tail Pulley: 8: Dia. x 18 in. Long
• Overall Dimensions: 36 in. Wide x 54 in. Long x 18 in. Deep
• Right Angle Gear Head Motor 
  • Ratio: 15:1
  • Tigear²
  • Part/Model: 20Q15H56
• Baldor Motor 
  • 1 HP 
  • 230/460 Volt
  • 1760 RPM
    Frame: 56C
• Location: British Columbia, Canada

View more Belt Magnets

1979 Grove TM 875 80 Ton Crane ID: 1242367

1979 Grove TM 875 80 Ton Crane

• Make: Grove
• Model: TM 875
• Capacity: 80 Tons
• Type: Hydraulic
• Year: 1979
• Hours: 3,953 Original Hours
• Miles: 14,100 Original Miles
• Condition: Used, Reported in Good Condition, Job Ready
• Dual Engines
  • Carrier Engine: CAT 3206
  • Super Structure Engine: CAT 3208
• Latest Load Electronics
• See Spec Sheets For More Info
  
  
• Location: Southwest USA

View More Mobile Cranes

Cefco 400 Amp 250 Volt Fuse ID: 526253

Amp: 400

Volt: 250 or less

One Time Fuse

Gorman Rupp 6 in Diesel Trash Pump ID: 180644

• Inlet: 6 in. (150 mm).
• Outlet: 6 in. (150 mm).
• Max. capacity: 1810-2700 GPM.
• Max. head: 150-195 ft.
• Max. solids: 3 in. (75 mm).

Please contact us for more information.

• View more Trash Pumps

Littelfuse INDICATOR Time-Delay 20 amp fuse ID: 360843

20 AMP

600VAC or less

Class: RK5

Length: 5"

Time Delay

Cummins 80kW Diesel Generator ID: 1403559

Cummins 80kW Diesel Generator

• Make: Cummins
• Model: C80D6R-1401512
• Year: 2014
• Hours: 4,554.4 Hours
• Condition: Used Condition
• Duty: Standby/Prime
• Portable/Stationary: Portable - Trailer Mounted
  • 3in Pintle Hitch
• Engine Model: QSB5-G2 Tier III
• Fuel Type: Diesel
• kVA/kW: 
  • Prime: 72kW (90kVA)
  • Standby: 80kW (100kVA) 
• Rotating Speed: 1800 RPM
• Voltage: 277/480 Volts - 12 Wire Reconnectable
• Current: 
  • Prime:
    • 120/208 Volts: 249.8 Amps
    • 120/240 Volts: 200.8 Amps
    • 139/240 Volts: 216.5 Amps
    • 277/480 Volts: 108.3 Amps
  • Standby:
    • 120/208 Volts: 277.6 Amps
    • 120/240 Volts: 223.3 Amps
    • 139/240 Volts: 240.6 Amps
    • 277/480 Volts: 120.3 Amps
• Frequency: 60Hz
• Phase: Single or 3-Phase
• Multiple Voltage Selector Switch
• Enclosure: Sound Attenuated 
• 27 Hour, 606 Liter Base Fuel Tank
  
  
• Overall Dimensions: With Trailer
  • Length: 4,495mm (177in)
  • Width: 1,905mm (77in)
  • Height: 2,083mm (85in)
  • Weight: 2,414 kg (5,322 lbs.)
    
    
• Location: Western Canada

View More 51-100kW Diesel Generators

Spendrup 42 in. Mine Ventilation Fan ID: 85043

• Model: EM 1120-70-6.
• 100 hp electric motor.
  • 460 volt.
  • 1765 rpm.
  • 405T frame.
• Curve available.
• Please inquire for additional details.

Montabert CPA X-TEND Boom ID: 1121082

Montabert CPA X-TEND Boom

• Make: Montabert
• Model: 24/20
• Condition: Good, Used
• Hours: 1200 Percussion Hours
• Feed Rail Looks to be in Very Good Condition
• Feed will take 24' Lead Steel and One 20' in Single Rod Holder
• T-51 Rods - Most Un-Used (x5)
• Comes With HC150 RP Montabert Drifter
• Includes Compressor (2,400 Hours)

CPA X-Tend Drilling Attachment 

• Works with HC150 RP or HC160 RP Montabert Drifters (based on model type)
• 76-140mm Hole Diameter
• 45-51mm Rod Diameter
• 3.6-28 Meter Maximum Hole Length (based on model type)
• 2170-2530 Blows/min
• Wired Control Panel
• Dimensions: 32' 8" Long x 4' 5" Wide x 6' Tall
• Weight: 2820Kg
• Carrier Characteristics
  • 22 to 35 Metric Tons
  • 88kW (119HP) Minimum Power Required
  • 195 l/min (51gpm) Required Oil Flow
  • 195 bar (2800 PSI) Required Oil Pressure 

These Attachments are ideal for the following applications:

• Quarry Holes for Blasting
• Trenches and Road Openings 
• Utility Works 
• Anchoring, Rock Bolting and Draining 
• Rough Terrain Construction
• High or Long Reach Drilling 

In Addition, The Drill Controls System Provides

• Straight Holes 
• Best Productivity
• Easy Drilling in Difficult Location or Rock Conditions 

HC150 Hydraulic Drifter

• 26-30 kW Maximum Output
• 37-50 kW Input Range
• 1,340-1,680 Nm Maximum Torque
• 76-115mm Hole Diameter
• 7,214-9,975mm Feed Length
• Type of Rod: T45, T51, T60
• Feed Swing: +/- 27°
• Air Requirement: 8,500-12,000 l/mm
• Weight: 190Kg
• Overall Length: 1,745mm
• Hydraulic Reserve Percussion 
• Application: Tunneling, Benching, Long Hole
  
  
• Location: Western Canada

View More Drilling Parts and Accessories 

Warman 300L Slurry Pump ID: 97729

• Model 300L.
• 14 in. x 12 in.
• Steel Lined.
• Overhead motor base.
• 5 vane steel impeller.
• Approx. Capacity:
  • 2,400 gpm @ 200 ft.
  • 13,000 gpm @ 130 ft.
    
    
• View Spec Sheet Below
  
  
• Location: Savona, British Columbia, Canada

General Electric 200 Amp 3 Pole Breaker ID: 586892

200 Amp

3 Pole

Cat No: FJ236200

600 V. AC

40C.

Ilsco D982 ID: 1304728

Ilsco D982

TA-500

CU-AL

500 MCM-4

In-floor Incline Belt Conveyor ID: 143321

• In-floor Incline Belt Conveyor.
  • Consists of:
    • 14 ft. horizontal section.
    • 26 ft. inclined section.
      • 60 in. wide belting.
  • Belt is one continuous loop driven by head pulley motor.

Please contact us for more information.

Siemens Size 4 Starter Contactor ID: 333603

• Size: 4
• Class: 3TF48
• Type: 1EC
• Coil: 120
• 3 Phase
• 60 Hz
• Location: British Columbia, Canada

View more Motor Starters

Hamilton H-3210 Parallel Shaft Gear Reducer ID: 75830

• 42.99:1 ratio.
• 59.3 hp.
• Size: H-3210.

Rietz 50ft³ Stainless Hopper with Auger Discharge ID: 1424432

Rietz 50ft³ Stainless Hopper with Auger Discharge

• Make: Reitz
• Model: C-12-K7208-6
• Condition: Used, Reported in Good Condition - Previously Used as Ore Hopper Feeding Rotary Dryer
• Construction: Stainless Steel
• Capacity: 50 Cubic Feet (Approx.)
• Top Section: 4ft x 5ft x 1ft
• Bottom Section: 4ft x 5ft x 3ft
• Top Opening: 4ft x 6ft
  
  
• Discharge: Auger Screw Discharge
  • Diameter: 12in Dia.
    • Open Top
  • Drive: Siemens Electric Motor
    • Power Output: 3HP
    • Rotating Speed: 875 RPM
    • Voltage: 460 Volt
    • Frequency: 60Hz
    • Phase: 3-Phase
      
      
• Location: Southwest USA

View More Hoppers

14in. Victaulic Gaskets ID: 236973

• Available: 48
• Location: Western Canada

View more Pipe Fittings

Sandvik AHM105 Voest Alpine Roadheader ID: 1205479

AHM105 Voest Alpine Roadheader

• Make: Voest Alpine (Sandvik)
• Model: AHM105 (MR620)
• Serial: AHM105019BG11
• Type: Roadheader - Hard Rock
• Hours: 6196.9
• Year: 2005
• Condition: Used
  
  
• Description: AHM105 (MR620) Hard-Rock Miner is an Electrically Powered and Crawler-Mounted Roadheader that is Engineered to Excavate Roadways and Galleries. This Heavy-Duty Machine has a Powerful Transverse Cutter Head Mounted on an Extremely Robust Telescopic Boom. It is Designed to Excavate Rock with High Compressive Strengths.
  
  
•  Specifications:
  • Machine Ground Pressure: 0.22 MPa
  • Loading Table Width (Variable): 5.5m-6.4m
  • Ground Clearance: 240mm
  • Cutting Height Above Track Level: 5.3m-5.8m
  • Cutting Width: 7.9m-8.5m
  • Undercut Below Floor Level: 500mm
  • Cutter Head Sprays: Jet Pipe
  • Cutting Speed (50Hz): 1.4m/sec
  • Navigable Cone Radius: 25m
  • Navigable Basin Radius: 25m
  • Navigable Slope Side Gradient: ±8/±9 gon
  • Slope Upgrade/Incline Without Stabilizing: ±18/±20 gon
  • Electric Supply Voltage (V/Hz): 1,000 Volt, 50Hz
  • Cutter Motor (kW): 300
  • Tramming Speed: 0-3.5m/min
  • Total Installed Power (kW): 522kW
    
    
• Additional Information:
  • Comes with Sea Can Full Of Parts
    
    
• Dimensions:
  • Length: 12.2m
  • Width: 3.6m - Table Width (2.6m - Tracks)
  • Height: 2.4m
  • Total Weight: 118 Tons Approx.
    
    
• Location: Western Canada

View More Roadheaders

Caterpillar 250 kW Marine Generator ID: 141991

• Caterpillar 250 kW Marine Generator.
  • New/surplus.
    • 397 hp @ 1800 rpm.
      • 254/440V.
        • 3 phase, 60 Hz.

Please contact us for more information.

Square D 400 Amp Safety Switch ID: 192831

• Model: HU365. 
• Volts: 600 VAC.
• Non-Fusible. 
• 3 Pole.  

View more 400 Amp Disconnects 

1,150 Gallon Mixing Tank & Mixer ID: 1173276

1,150 Gallon Mixing Tank

• Size: 73" Diameter x 63" Tall
• Volume: 1,150 US Gallons
• 4 Internal Baffles:
  • 51" x 6" x 1"
  • 1" Gap to Tank Wall
  • 6" Off Bottom
• Pedestal Tank Mixer
  • Model: Dynamix DMX-5520J-2
  • Mixer Shaft: 65.75" Long x 1.25" Diameter
  • Propeller: Stainless Steel
    • 19" Diameter
      • Pitched Blade
    • Comes with second 9.75" diameter radial blade propeller
    • Medium Mixing Level
    • Approx. 13" Off Bottom of tank
      
      
  • Mixer Motor: TEFC Electric Motor
    • 2HP
    • 1750 RPM
    • 230/460V
    • 60Hz, 3-Phase
  • Inline Reducer:
    • 11:1 Ratio
    • 159 RPM
      
      
• Bridge on Top of Tank
  • Made From 3" x 3" Angle 
  • Mixer Support Plates made from HDPE
  • Mixer Mounting Plate Made From Stainless Steel
    • 11" x 11" Plate
    • 3" Diameter Center Hole
    • 2.5" Tall 3/8 Studs Spaced 4" Apart
      
      
• Mixing Tank Lid
  • Size: 73" Diameter x 19" Tall
  • Notched for Mixer Mount Bridge
  • Man Hole with Lid: 18" Diameter
  • Center Hole for Mixer: 13" Diameter
  • 8" x 7" Cutout
  • Lifting Handles
    
    
•  Fittings
  • 2" Male and Female
  • 6 Total - 2 Female, 4 Male
  • 3 Holes @ 59.5" High
  • 2 Holes @ 13.0" High
  • 1 Hole @ 2.16" High
    
    

• Location: Savona, British Columbia, Canada

View More Agitators and Mixers